Art.Nr.: 300054874 Artikelbezeichnung: TT-02 Querlenker-Set oben/einstellbar?These upper arms allow setting of camber angle between 0 and 2 degrees via adjustment of turnbuckle shaft.?Use Item 42236 when adjusting.Compatible ChassisTT-02, TT-02RR &  TT-02D Chassis *Use with Item 53792 Assembly Universal Shaft (TT-01, TA04).  

Art.Nr.: 300054868Artikelbezeichnung: 5mm Kugelpfanne Med./11,5mm (8) offen- Open Face 5mm Reinforced Adjusters (Medium) x8- Length: 11.5mm- May require filing down when used on some models.  

Art.Nr.: 300051620Artikelbezeichnung: M-08C C-Halter 2Grad (2) VorspurCrashes and bumps can sometimes leave you needing new upright components, and Tamiya has drivers of the new M-08 Concept RWD chassis covered with the release of these spare parts.Item Contents/Information• M-08 Concept C Parts sprues x2• Sprue contains front* and rear uprights*, hub carriers, and adapters.• Hub carrier parts give a caster angle of 2 degrees.• Compatible with M-07 and M-08 Concept chassis cars.*denotes shared design with M-07 Concept.  

Art.Nr.: 300054869Artikelbezeichnung: 5mm Kugelpfanne Long/15mm (8) offen- Open Face 5mm Reinforced Adjusters (Long) x8- Length: 15mm- May require filing down when used on some models.  

Art.Nr.: 300054875 Artikelbezeichnung: TT-02 Kegeldiff.-Öl befülltTamiya is delighted to announce that the gear differential unit from the recently-released TT-02RR Chassis Kit (Item 47382) is to be released as its own Hop-Up Option part!Item Contents/Information• Glass fiber-reinforced Nylon Gear Case Parts x1• Gasket x1• Die-Cast Bevel Gears x4• Oil-filled gear differential units facilitate smooth,  efficient drive. Use different grades of oil, gear diff putty,  etc. to quickly adjust your setup.• Compatible with TT-02 series chassis (Item 53792 required  for TT-02, TT-02D; Item 53791 required for TT02B).  

Art.Nr.: 300051624 Artikelbezeichnung: 3x6mm 6-Kantkopf Schraube Stahl (10)?These are durable steel screws with hex heads for secure tightening.?Replace parts in a timely fashion to ensure that your car runs at peak performance.  

Art.Nr.: 300054860 Artikelbezeichnung: T3-01 370 Sport-Tuned Motor?This tuned motor is perfect for use with the R/C Dancing Rider, and offers dynamic drive. ?Input voltage: 6.6-7.2V?RPM: 22,200 (at 7.2V)?Maximum torque: 4.91mN-m?Maximum usage: 2.85ACompatible ChassisT3-01 Chassis *Use with Item 54228 Fluorine Coated 06 Module Pinion Gear (26T, 27T), Item 54834 T3-01 Full Ball Bearing Set, Item 54857 T3-01 One-Piece Rear Axle Shaft Set and Item 54876 T3-01 Reinforced Differential Joint & Pinion Set. **Item 55105 LF1100-6.6V Racing Pack (M-Size) is required as a power source..  

Art.Nr.: 300054871 Artikelbezeichnung: V-Teile TRF Dämpfer verstärktGive your TRF dampers an overhaul with this completely redesigned set of V Parts, made to give you more setup options. The new designs and material also boost durability and damper performance.Item Contents/Information• ø5mm Damper Ends (S) & (M)• ø5.8mm Damper Ends (S) & (M)• ø5mm Damper Tops• ø5.8mm Damper Tops• Spring Retainers (S) & (M)• Compatible with TRF Dampers (Items 53571,  53901, 54000 etc.) using Item 53334.  

Art.Nr.: 300054891 Artikelbezeichnung: M-08C Alu Lenkhebel (L/R) Blau elox.Sharpen up the M-08 Concept’s steering even further with these aluminum steering arms! More precise motion leads to a direct steering feel. Aluminum parts offer extremely secure attachment.Item Information/Contents• Aluminum Steering Arm (Right) x1• Aluminum Steering Arm (Left) x1• Steering arm components are given the iconic Tamiya  blue anodized finish.• Recommended for use with separately sold steering bridge  (Item 54892).• Compatible with M-08 Concept chassis.  

Art.Nr.: 300054892Artikelbezeichnung: M-08C Alu Lenkhebelverb. Blau elox.This aluminum steering bridge for the new M-08 Concept chassis will give more precise steering motion and more secure attachment of components.Item Information/Contents• Aluminum Steering Bridge x1• Component has the iconic Tamiya blue anodized finish.• 5.5x2mm and 5.5x1.5mm Spacers (x2 each) are included to adjust clearance.• Recommended for use with separately sold steering arms (Item 54891).• Compatible with M-08 Concept chassis.  

Art.Nr.: 300051625 Artikelbezeichnung: 3x6mm 6-Kant-Senkkopf Schraube Stahl(10)?These are durable steel countersunk screws with hex heads for secure tightening.?Replace parts in a timely fashion to ensure that your car runs at peak performance.  

Art.Nr.: 300051626Artikelbezeichnung: 3x8mm 6-Kantkopf Schraube Stahl (10)?These are durable steel screws with hex heads for secure tightening.?Replace parts in a timely fashion to ensure that your car runs at peak performance.  

Art.Nr.: 300051627Artikelbezeichnung: 3x8mm 6-Kant-Senkk. Schraube Stahl(10)?These are durable steel countersunk screws with hex heads for secure tightening.?Replace parts in a timely fashion to ensure that your car runs at peak performance.  

Art.Nr.: 300051628Artikelbezeichnung: 3x10mm 6-Kantkopf Schraube Stahl (10)?These are durable steel screws with hex heads for secure tightening.?Replace parts in a timely fashion to ensure that your car runs at peak performance.  

Art.Nr.: 300051629Artikelbezeichnung: 3x10mm 6-Kant-Senkk. Schraube Stahl(10)?These are durable steel countersunk screws with hex heads for secure tightening.?Replace parts in a timely fashion to ensure that your car runs at peak performance.  

Art.Nr.: 300051630Artikelbezeichnung: 3x12mm 6-Kantkopf Schraube Stahl (10)?These are durable steel screws with hex heads for secure tightening.?Replace parts in a timely fashion to ensure that your car runs at peak performance.  

Art.Nr.: 300054893Artikelbezeichnung: Alu Servohorn-Set einst. m. HT-Servos.?Set distance between servo horn center and ball connector at 1m increments between 15 and 22mm.?Steering range is also adjustable.?Incorporates servo saver function, providing protection in case of crashes and other shocks.Compatible ChassisCC-01, GF-01, G6-01, M-05, M-05 PRO, M-05Ra, M-05 Ver.II PRO, M-06, M-06 PRO, M-07 Concept, M-08 Concept, TA07 PRO, TA07 MS, TB-05 PRO, TT-02 & TT-02B Chassis  

Art.Nr.: 300054921 Artikelbezeichnung: Blades verstärkt (2) f. 54879?These reinforced caps hinder wear and tear of swing shafts. Change them regularly to ensure peak performance.?Use with Item 54879 TRF419 Aluminum Front Direct Cups (2pcs.).  

Art.Nr.: 300054882Artikelbezeichnung: TRF Alu E (C-G) Querlenkerh. (1)These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions.Contents/Information• Aluminum Adjustable Suspension Mount (E) x1• Bushings Sprue x1• This mount allows settings between C and G (toeangles depend upon separate suspension mounts andbushings used).• Mount has the iconic Tamiya blue anodized finish.• Compatible with TRF419, TA07 and TB-05 chassis cars.  

Art.Nr.: 300054884Artikelbezeichnung: TRF Alu A-a/A-b (XA-C) Querlenk. (1/1)These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions.Contents/Information• Aluminum Adjustable Suspension Mount (A-a), (A-b) x1 each• Bushings Sprue x1• This mount allows settings between XA and C (toeangles depend upon separate suspension mounts andbushings used).• Mount has the iconic Tamiya blue anodized finish.• Compatible with TRF419, TA07 and TB-05 chassis cars.  

Art.Nr.: 300054885Artikelbezeichnung: TRF Alu E-a/E-b (C-G) Querlenk. (1/1)These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions.Contents/Information• Aluminum Adjustable Suspension Mount (E-a), (E-b) x1 each• Bushings Sprue x1• This mount allows settings between C and G (toeangles depend upon separate suspension mounts andbushings used).• Mount has the iconic Tamiya blue anodized finish.• Compatible with TRF419, TA07 and TB-05 chassis cars.  

Art.Nr.: 300054924Artikelbezeichnung: GF-01/TR Kugellager-Satz (24+2)Highly efficient, smooth power awaits with the installation of this set of ball bearings that includes just the right number to fully kit out the GF-01 chassis.Set Contents/Information• 1150 Ball Bearings x24• 850 Ball Bearings x2• Install in place of kit standard plastic and metal bearings.• Compatible with GF-01 chassis models.  

Art.Nr.: 300054925Artikelbezeichnung: G6-01TR/GF-01TR 630 Kugellager (8)Ball bearings are an excellent first step when tuning up your chassis from box stock, providing more efficient drive and longer lasting fun thanks to less wear and tear on moving parts. The 630 ball bearings in this set are for use in the reduction gears on the G6-01TR and GF-01TR chassis.Item Contents/Information• 630 Ball Bearings x8• For use in the reduction gears on G6-01TR and GF-01TR chassis models. Each reduction gear requires two 630 ball bearings – sixteen total (two of this set) to kit out the GF-01, or twenty-four (three of this set) to kit out the G6-01.• Compatible with GF-01TR and G6-01TR chassis cars.  

Art.Nr.: 300051634Artikelbezeichnung: CC-02 J-Teile Kar.-Halter- 1/10 Karosseriesatz, Bausatz für M-Chassis Modelle- unlackiert- durchsichtiges Polycarbonat- beinhaltet Anbauteile wie Spiegel und Lampeneinsätze- Inklusive Maskierfolie für die Fenster- Kompatibel für M-Chassis Modelle mit 239 mm Radstand- für die Lackierung werden TAMIYA PS Farben für Polycarbonat Karosserien benötigt